LAB GRUPPEN เพาเวอร์แอมป์ FP 6000Q เครื่องขยายเสียง กำลังวัตต์สูง delivers a total of 6000 W (4 x 1500 W @ 2 ohms) in only  2U 

 

A Benchmark For Touring Amplification

Over the past decade, the tight and transparent sound of 

Lab.gruppen touring amplifiers has earned the praise of renowned 

FOH engineers and leading sound rental companies worldwide. 

FP 6000Q, the second four-channel model of the FP+ Series, continues this tradition. At the core of the FP 6000Q’s performance 

is the patented Class TD output stage, a breakthrough amplifier 

topology that approaches the exceptional efficiency of Class D 

while retaining the sonic purity of proven Class B designs. Further 

contributing to the remarkable efficiency of the FP 6000Q is a 

Regulated Switch Mode Power Supply (R.SMPS), which gives the 

added benefit of stabilizing rail voltages to the output even with wide 

fluctuations of mains voltage. A highly refined and updated circuit 

layout optimizes the interaction of R.SMPS and Class TD to produce 

the extraordinary power and channel density of the FP 6000Q.

To keep its cool under extreme demands, the FP 6000Q relies on 

Lab.gruppen’s proprietary Intercooler®. This innovation uses thousands of copper fins to multiply the exposed heatsink surface’s 

rapid heat dissipation. Also, all output devices are mounted transverse to the airflow for uniform cooling. As a result, the FP 6000Q 

delivers Lab.gruppen’s’ trademark “all the power, all the time” with 

no degradation of sonic performance.

To maximize headroom in any application, the FP 6000Q offers 

adjustable input gain along with Lab.gruppen’s exclusive Voltage 

Peak Limiter (VPL). Adjustable on a per-channel basis, VPL optimizes 

the output for any load, from a single massive subwoofer to a series 

of HF compression drivers.

The comprehensive warning and protection features on the 

FP 6000Q safeguard output circuits and connected loads while also 

extending amplifier life and minimizing the chance of service interruptions. Whether it’s a matter of faulty wiring, improper use, or 

extreme ambient temperatures, the FP 6000Q gives clear indication 

of any problems. Automatic protection measures engage only at critical thresholds, and conditions are re-checked every six seconds with 

normal operation resumed when measurements return to nominal.

The FP 6000Q is shipped with a NomadLink® network interface as 

standard. In conjunction with DeviceControl software, NomadLink®

allows monitoring of all key amplifier parameters and remote control of power on/off, channel mutes, and channel solo functions. 

(NomadLink® requires the separate NLB 60E NomadLink® Bridge & 

Network Controller).

Specifications FP 6000Q

 

General

Number of channels 4

Peak total output all channels driven 6000 W

Peak output voltage per channel 101 V

Max. output current per channel 27 Arms 

Max. Output Power 2 ohms 4 ohms 8 ohms 16 ohms

Per ch. (all ch.’s driven) 1500 W 1250 W 625 W 320 W

Bridged per ch. - 3) 3000 W 2500 W 1250 W

Performance with Gain: 35 dB and VPL: 101 V

THD 20 Hz - 20 kHz for 1 W <0.1%

THD at 1 kHz and 1 dB below clipping <0.05%

Signal To Noise Ratio >112 dBA

Channel separation (Crosstalk) at 1 kHz >70 dB

Frequency response (1 W into 8 ohms) +0/-3 dB 6.8 Hz - 34 kHz

Input impedance 20 kOhm

Input Common Mode Rejection, CMR 50 dB

Output impedance @ 100 Hz 56 mOhm

Output slew rate into 8 ohms 20 V/microsecond

Voltage Peak Limiter (VPL), max. peak output 

VPL, selectable per ch. 101, 83, 70, 56, 47, 38 V

VPL, selectable when bridged 1) 202, 166, 140, 112, 94, 76 V

Voltage Peak Limiter mode (per ch.) Hard / Soft

Gain and Level

Amplifier gain selectable (all channels) 1)

– rear-panel switches

23, 26, 29, 32, 35, 38, 41, 44 dB

Default gain 35 dB

Level adjustment (per ch.) Front-panel potentiometer, 21 position detented from -inf to 0 dB

Connectors and Switches

Input connectors (per ch.) 3-pin XLR, electronically balanced

Output connectors (per ch.) Neutrik Speakon or Binding Posts (must be specified upon order)

Output bridge mode A+B, C+D - Ch.’s A and C are signal input source

NomadLink® network On board, 2 x RJ45 EtherCon connectors, IN and OUT

Intelligent fans (on/off) Yes, depending on presence of output signal

Power on/off and Remote enable on/off Individual switches on front-panel

Cooling Two fans, front-to-rear airflow, temperature controlled speed

Front-panel indicators:

Common NomadLink® Network; Power Average Limiter (PAL) 2); Power on 

Per channel Signal present / High-impedance; -20 dB, -15 dB, -10 dB and -4 dB output signal; 

Voltage Peak Limiter (VPL); Current Peak Limiter (CPL): Very High Frequency (VHF); High temperature; Fault; Mute

Power

Operating voltage, 230 V / 115 V nominal 4) 130-265 V / 65-135 V

Minimum power-up voltage, 230 V / 115 V 171 V / 85 V

Power Average Limiter (PAL) 2) Yes

Soft start / Inrush Current Draw Yes / max. 5 A

Mains connector 230 V CE: 16 A, CEE7; 115 V ETL: 30 A Twist lock

Dimensions (W/H/D) W: 483 mm (19”), H: 88 mm (2 U), Overall D: 396 mm (15.6”), Mounting D: 358 mm (14.1”) 

Weight 12 kg (26.4 lbs.)

Finish Black painted steel chassis with black painted steel / aluminum front

Approvals CE, ANSI/UL 60065 (ETL), CSA C22.2 NO. 60065, FCC